To keep your pool’s water sparkling clean, a few basic maintenance steps are required. Find information on the usage of products, care and how to test your water for easy pool maintenance in this section.
Testing Your Pool – Testing your pool 2-3 times a week during the summer and once a week during the winter is important to maintain adequate water balance and sanitizer levels plus to insure swimmer comfort. Test strips are a quick way to test the pool for adequate sanitizer levels as well as pH and total alkalinity. Proper testing also ensures that calcium levels are maintained and that there are no metals present in the pool water. These tests can be completed by you or your pool professional. In order to prevent scaling or corrosive action and to achieve maximum swimmer comfort, Pool Management jobs, the pool water should be balanced.
Balancing pH – pH is the measure of acid and base in the pool water. The pH of the pool should be tested and adjusted, if necessary, on a weekly basis. If the pH of the pool water drifts to the acid side of the scale, corrosion of pool surfaces and equipment can occur. If the pH of the pool water drifts to the base side – scaling, deposits, and cloudy water can occur. Use a pH increaser to increase the pH of the pool. At 8.5, chlorine is only about 10% active. At 7.0, chlorine is about 73% active. If you maintain pH around 7.5, the chlorine will be 50-60% active. Keeping the pH in check will allow you to use the full potential of the chlorine that is already in the pool. To lower the pH of the pool, use a pH decreaser. Follow the label directions for the proper amount of the products to add based upon test results and pool size & Swimming Pool Management. Take a sample of water to your pool professional dealer every 2-3 weeks for complete test and analysis.
Calcium Hardness – Calcium Hardness is the amount of dissolved calcium in the pool water. Low calcium hardness levels can cause plaster finish etching and shorten the life of vinyl liners. High calcium levels can result in calcium deposits on the pool surfaces as well as equipment. The proper range for calcium hardness in pool water is 200- 250 ppm (parts per million) for concrete pools and 175-225 ppm for vinyl pools. Your pool professional can advise you of the best method for treating your pool & Swimming Pool staffing if you encounter high calcium hardness. If tests indicate that you have extremely high calcium levels in your pool, take a sample of your fill water (water used to fill the pool) to your pool professional for analysis as well.
Total Alkalinity – To prevent the pH varying up and down, the proper amount of acid buffers, or total alkalinity, must be maintained in the pool. The pool should be tested weekly with a total alkalinity of 1 20-150 ppm (parts per million) maintained. Low total alkalinity can not only result in pH bounce and fluctuations, but corrosiveness and the possibility of staining increase. High total alkalinity also can cause the pH to fluctuate as well as cause cloudy pools along with possible scaling. To lower total alkalinity, follow the directions from your pool professional. To raise total alkalinity, an alkalinity booster is recommended Lifeguards & Lifeguarding.
Metals – There should not be any metals present in your swimming pool water. Metals can cause staining in the pool and cause the pool to turn colors. The most common types of metals that appear in pool water are copper, iron, and manganese. If metals are present in the pool, a stain and scale remover should be used on a regular basis to prevent staining. You should determine the source of the metals and remove if possible.
Sanitize with Chlorine – Stabilized chlorine products sanitize your pool water and kill bacteria. Stabilized chlorine products are protected from sun light degradation and are an ideal means to keep your pool clear and clean & Aquatic Management.
Sanitize with Bromine – You may want to use bromine instead of chlorine to sanitize your pool. Bromine tablets provide a reliable method for killing bacteria and keeping your pool clear and clean. To utilize bromine effectively, an automatic brominator should be installed in your pool.
Shock – Shocking the pool on a regular basis is an important element in keeping the pool clear and clean. Swimmers and the environment add waste to the pool that must be eliminated on a regular basis in order to prevent problems such as algae and cloudy water.
Algaecide – Preventing algae is the key to an enjoyable pool. Algaecides act as a backup to your normal sanitization program and prevent algae from starting and growing in the pool. Algaecide should be added after every shock treatment.
PMI is a professional full service Pool Management jobs that provides staffing solutions for Aquatic Management companies water parks, community pools and city pools. We manage facilities in multiple states and can provide you with multiple solutions for your facility.